Weed Eater SST LE Weed Eater Featherlite String Trimmer (Type 1 from www.partstree.com
Weed Eater Carburetor Diagram. Remove the rear cover from the engine. It proves the big help under.
Pull this fuel line through the gas tank opening. Test the fuel line routing with the carburetor. You will be adjusting the screw from the front of the engine. Locate the idle adjustment screw on your trimmer. Pull out about 1 of fuel line from the fuel cap opening and attach filter. The smaller diameter line (fuel supply) goes from the fuel tank (w/filter) to the carb body. Some walbro carburetors do not have the manual pumper and must rely upon an external manual pumper to prime the carburetor. Keeping tension on the rope, allowing the rotor to unwind while you guide the rope into the groove around the rim. If your weed eater is hard to start or stops running, and if you have to choke it to keep it running this could be the answer to a quick fix.
Take A Digital Photograph Of How The Throttle Cable Control Cable Connects To The Carburetor Or Make A Diagram.
Husqvarna fuel line parts diagram trimmer gas weed eater 323l 323c 325l sys clutch ignition prior 2004 looking spring carb. Thread the other end of the rope through the starter cover and through the starter grip. On this page you will find every weedeater model and a link to the exploded parts diagram and catalogue. At first, identify the carb of your weed eater. Drain any excess fuel from the fuel tank prior to servicing the carburetor or the fuel lines. Attach the incoming line on the primer assembly to one of the ports on the carburetor and attach a third. It is easy and free The manual pumper is required to prime the carburetor before the engine will start. Now, locate the screws that adjust the fuel supply.
The Screw Responsible For The Engine Idling (“T” Or “At”).
Keeping tension on the rope, allowing the rotor to unwind while you guide the rope into the groove around the rim. It proves the big help under. Rotate both of these screws in the clockwise direction until they are tight. Remove the rear cover from the engine. Cut off the extra rope with a knife. Insert the round, circular loop at the other end of the primary spring into the corresponding. Now prepare to adjust their individual positions. Poulan carburetor november 4, 2020. To be specific, you need to remove the plate that attaches the primer bulb to the primer base.
The Smaller Diameter Line (Fuel Supply) Goes From The Fuel Tank (W/Filter) To The Carb Body.
Drain any liquid that is in the carburetor. 530069647, 530069665, 530069683, 530069902, 530071639. The carburetor itself is a fuel pumper in the way that it draws fuel from the fuel tank with no external pump and in any carb/tank position. Remove the (2) screws from the carburetor assembly. Test the fuel line routing with the carburetor. The thin line is your fuel feed while the thick one is your fuel return/breather. Pull this fuel line through the gas tank opening. Complete exploded views of all the major manufacturers. If your weed eater is hard to start or stops running, and if you have to choke it to keep it running this could be the answer to a quick fix.
The Only Adjustments That The Owner Can Perform On The Carburetor Is The Idle Adjustment.
Use this basic procedure to rebuild the carburetor using a weed eater carburetor rebuild kit on craftsman, mtd, toro, weed eater, troybilt, snapper, cub cadet and poulan line trimmers. When replacing the thin line, it connects to the filter inside the tank. Push the small fuel line into the other hole in the gas tank. Generally, the position of the carb of most of the weed eaters is between the air filter and the fuel bulb. Worldwide shipping, no hassle returns. Remove the (4) screws from the rear cover. Just bought a replacement purge bulb and 2 fuel line kits (one. There are two screws on the carb. Some walbro carburetors do not have the manual pumper and must rely upon an external manual pumper to prime the carburetor.
Post a Comment
Post a Comment